• HFG 6
  • HFG 6
  • HFG V Elektro

The Shredder HFG V is a powerful, cost-saving machine and applicable in a variety of ways.

The hopper with a length of 4.800 mm and a width of 1.900 mm is equipped with an infeed belt. The infeed material is mecanically conveyed via infeed belt to the rotor with freely swinging hammers. The infeed opening has a height of 540 mm and a width of 1.500 mm. Thus, material of up to 300 mm can be processed.

Schlegelhäcksler HFG VI

  • Features of the basic machine 

    Infeed belt: •Highly wear resistant, forged special chain

    •Width of infeed belt: 1.500 mm

    •Length of infeed belt: 4.000 mm

    Hydraulic system: •Infeed roller and infeed belt are powered each by a separate drive and gear. The speeds of infeed belt and of the infeed roller are infinitely variable. Overload protection through speed monitoring and reversing device.

    Hydraulic tank with a capacity of 220 litres.

    Infeed: •The infeed roller is powered hydraulically , is pendulum mounted and guided by two racks.

    •The infeed opening is approx. 540 mm high and 1.500 mm wide.

    Crushing unit: •42 hammers, hammer width: 80 mm

    •Single hammers replaceable

    •Width of crushing unit: 1.500 mm

    •Rotor diameter: 1.000 mm

    •Rotor speed: 1.000 rpm

    Engine: CAT turbo diesel with a power of P = 354 kW, valid  Euro emission standard

    •Electric motor with a power of P = 250 kW

    Drive: •Direct drive by 8  V-belts
    Hopper dimensions: •Length of hopper opening: 4.800 mm

    •Width of hopper opening: 1.900 mm

    Throughput: •100-200 m³/hr and more, depending on material

  • Machine description



    These powerful Husmann machines with the basic designation “HFG (Husmann Forestry Equipment)” achieve an even, fine and clean comminution due to the special shredding technology and the hammer positioning.

    The shredding principle, long-term experience and high quality mark the systems produced by Husmann.

    The material to be processed is conveyed via the amply dimensioned hopper including a forged steel chain conveyor to the infeed roller and further to the hammer equipped rotor. The pendulum mounted infeed roller is giuded by racks and hydraulically powered with a large reduction gear. The infeed roller adapts itself to the supplied material. It can additionally be controlled and lifted by remote control.  The roller or also passage opening of 550 mm guarantees smooth and quick infeed.

    The stable rotor (1.500 kg) made of high-quality steel is highly break-resistant due to additional reinforcements and the mature design even in case of heavy foreign material. The eight hardened hammer shafts are equipped with 42 freely swinging hammers mounted in offset alignment. The quick-change system includes the bolting of the carbide tipped hammers to the hammer carriers. With the many 80 mm wide hammers and the rotor´s rotational direction over the breaker bar towards the infeed belt, the shredding material is optimally crushed and then compostable. The load-dependent and infinitely variable infeed speed of the scraper floor and the infeed roller can again influence and improve the quality of the end product. The rotor tray and the discharge area allow the attachment of a stack of 2,5 metres.

    The powerful Caterpillar engine with 354 kW diesel engine or 250 kW electric motors is well accessible through large doors, making it operator- and maintenance-compatible. A hydraulic tensioning roller transmits the engine power gently and with low wear to the crushing unit, in particular when starting up. Well-structured operating elements and safety devices like rotor and auto reverse are quality features of our machine.

    The overload protection of the rotor and the auto reverse system guarantee optimal control and machine operation.
    The standard mobile comminution machine is equipped with a 80 km/hr chassis, compressed air brake and ABS system.
    The HFG V is a composting machine for organic and inorganic waste for mecanical and manual feeding.
    Material processing up to approx. 300 mm



    HFG 6

    Schlegelhäcksler HFG V Mobilgerät

      • Turbo-Diesel, 254 kW, gültige Abgasnorm
      • Tank volume: 500l diesel tank
      • Geschweißte Stahlprofilkonstruktion mit einem Zugmaul nach DIN
      • Tandem-Tiefladeraggregat ca. 18 to.
        TÜV-Abnahme für 80 km/h Achse
      • druckluftgebremst
      • ABS-Bremsanlage
      • Zweileitungs – Druckluftbremsanlage für 80 km/h Achse
      • 4 Stück mit der Größe 385/65R 22.5 auf 22.5 x 11.75 Felge
      • Eigengewicht: ca. 18.500 kg
      • zul. Achslast: 20.000 kg
      • Stützlast: 500 kg
      Abmessungen: (gemäß Aufstellplan)
      • Gesamtlänge: ca.12.700 mm
      • Breite: 2.500 mm
      • Höhe: ca. 3.990 mm
      • Einwurfhöhe: 2.100 mm


    HFG V Elektro

    Schlegelhäcksler HFG V elektro stationär

      • Elektromotor, 250 kW (+22kW Nebenantrieb)
      • Stabile Stahl-Schweißkonstruktion gemäß Anwendungsfall
      • ca. 18.000 kg
      Abmessungen: (gemäß Aufstellplan)
      • Gesamtlänge: ca.9.560 mm
      • Breite: 2.500 mm
      • Höhe: ca. 3.870 mm
      • Einwurfhöhe: 2.000 mm

    Infos anfordern !

    Sie möchten mehr über unser Produkt wissen?

    Lassen Sie uns gerne eine Mail zukommen unter info@husmann-web.de

    Optionales Zubehör HUSMANN Schlegelhäcksler

    Über verschiedenes Zubehör kann die Grundausstattung der HUSMANN Schlegelhäcksler den Wünschen und den Anwendungen der Kunden nach angepasst werden. Hierzu gehören unter anderem ein individuelles Austragsförderband, eine TÜV-Abnahme, oder auch der Überlastschutz.

    Des weiteren können Sie folgendes optionale Zubehör wählen:

    • Funkfernbedienung
    • Förderband
    • hydr. Fahrantrieb
    • Magnet – Antriebstrommel
    • Sieb hydr. klappbar
    • Wechsellüfter
    • Trichterschütte klappbar
    • Stützfuß hydraulisch
    • Fahrzeugbrief
    • Sonderlackierung (Standart RAL 5010) uvm.