• HFG IV
  • HFG IV
  • HFG IV Einzug
  • HFG IV Hakenlift
  • HFG IV Hakenlift
  • HFG IV Hakenlift
  • HFG IV Fahrantrieb
  • HFG IV Einzug
  • HFG IV Innenansicht
  • HFG IV Sieb
  • HFG IV elektro stationär

The goal of the planning of the Shredder HFG IV was to develop a powerful, cost-saving and versatile shredding machine.

The infeed hopper with a length of 3.450 mm and a width of 1.800 mm is equipped with an infeed belt. The infeed material is mecanically conveyed via infeed belt to the rotor with freely swinging hammers. The infeed opening has a height of 400 mm and a width of 1.230 mm. Thus, material of up to 200 mm can be processed.

Schlegelhäcksler HFG IV

  • Features of the basic machine

    Infeed belt: Highly wear-resistant, forged special chain

    Infeed belt width:  1.230 mm

    Infeed belt length: 3.450 mm

    Hydraulic system: Infeed roller and infeed belt with one separate drive and gear each. The speeds of infeed belt and infeed roller are infinitely variable. Overload protection due to speed monitoring and auto reverse.
    Hydraulic tank with a capacity of 140 litres.
    Infeed: The infeed roller is hydraulically powered, pendulum mounted and guided by 2 racks.

    The infeed opening is approx. 400 mm high and 1.230 mm wide.

    Shredding unit: 60 hammers, hammer width: 50 mm

    Single hammers are replaceable

    Width of shredding unit: 1.230 mm

    Rotor diameter: 850 mm

    Rotor speed: 1.000 U/min

    Engine: CAT turbo diesel with a power of P = 205 kW, valid Euro exhaust standard

    Elektric motor with a power of P = 200 kW

    Drive: Direct drive by 8 V-belts
    Hopper dimensions: Length of hopper opening: 3.450 mm

    Width of hopper opening:  1.800 mm

    Throughput: 60-100 m³/hr depending on material and feeding device

  • Machine description


    These powerful Husmann machines with the basic designation “HFG (Husmann Forestry Equipment)” achieve an even, fine and clean comminution due to the special shredding technology and the hammer positioning.

    The material to be processed is conveyed via the amply dimensioned hopper including a forged steel chain conveyor to the infeed roller and further to the hammer equipped rotor. The pendulum mounted infeed roller is guided by racks and hydraulically powered by a large reduction gear. The infeed roller adapts itself to the supplied material. It can additionally be controlled and lifted by remote control. The roller or also passage opening of 460 mm guarantees smooth and quick infeed.

    The stable rotor (1.000 kg) made of high-quality steel is highly break-resistant due to additional reinforcements and the mature design even in case of heavy foreign material. The eight hardened hammer shafts are equipped with 60 freely swinging hammers mounted in offset alignment. The quick-change system includes the bolting of the carbide tipped hammers to the hammer carriers. With the many 50 mm wide hammers and the rotor´s rotational direction over the breaker bar towards the infeed belt, the shredding material is optimally crushed and then compostable. The load-dependent and infinitely variable speed of the scraper floor and the infeed roller can again influence and improve the quality of the end product. The rotor tray and the discharge area allow the attachment of a stack of 2,5 metres.

    The powerful 205 kW engine is well accessible through large doors, making it operator- and maintenance-compatible.  Well structured operating elements and safety devices like overload protection of the rotor and auto reverse are quality features of our machine.

    The mobile comminution machine is equipped with a 80-km/hr chassis and compressed air brakes and optionally static or with a hook-lift system.

    The HFG IV is a composting machine for organic and inorganic waste for mecanical and manual feeding.

    Material processing  up to approx. 200 mm



    Schlegelhäcksler HFG IV Mobilgerät

      • Turbo-Diesel, 205 kW, gültige Abgasnorm
      • Geschweißte Stahlprofilkonstruktion mit einem Zugmal nach DIN
      • Tandem-Tiefladeraggregat ca. 14 to.
        TÜV-Abnahme für 80 km/h Achse
      • druckluftgebremst
      • ABS-Bremsanlage
      • Zweileitungs – Druckluftbremsanlage für 80 km/h Achse
      • 4 Stück mit der Größe 265/70R 19.5 auf 19.5 x 7.50 Felge
      • Eigengewicht: ca. 11.500 kg
      • zul. Achslast: 13.500 kg
      • Stützlast: 500 kg
      Abmessungen: (gemäß Aufstellplan)
      • Gesamtlänge: ca.7.650 mm
      • Breite: 2.350 mm
      • Höhe: ca. 3.000 mm
      • Einwurfhöhe: 1.720 mm

    Schlegelhäcksler HFG IV elektro stationär

      • Elektromotor, 200 kW
      • Stabile Stahl-Schweißkonstruktion gemäß Anwendungsfall
      • ca. 12.000 kg
      Abmessungen: (gemäß Aufstellplan)
      • Gesamtlänge: ca.7.650 mm
      • Breite: 2.300 mm
      • Höhe: ca. 3.650 mm
      • Einwurfhöhe: 2.200 mm

    HFG IV Hakenlift

    Schlegelhäcksler HFG IV Hakenliftrahmen

      • Turbo-Diesel, 205 kW, gültige Abgasnorm
      • Geschweißte Stahlkonstruktion mit Containerschlitten und Hakenaufnahme
      • ca. 11.000 kg
      Abmessungen: (gemäß Aufstellplan)
      • Gesamtlänge: ca.8.550 mm
      • Breite: 2.300 mm
      • Höhe: ca. 3.095 mm
      • Einwurfhöhe: 1.7400 mm

    Infos anfordern !

    Sie möchten mehr über unser Produkt wissen?

    Lassen Sie uns gerne eine Mail zukommen unter info@husmann-web.de

    Optionales Zubehör HUSMANN Schlegelhäcksler

    Über verschiedenes Zubehör kann die Grundausstattung der HUSMANN Schlegelhäcksler den Wünschen und den Anwendungen der Kunden nach angepasst werden. Hierzu gehören unter anderem ein individuelles Austragsförderband, eine TÜV-Abnahme, oder auch der Überlastschutz.

    Des weiteren können Sie folgendes optionale Zubehör wählen:

    • Funkfernbedienung
    • Förderband
    • hydr. Fahrantrieb
    • Magnet – Antriebstrommel
    • Sieb hydr. klappbar
    • Wechsellüfter
    • Trichterschütte klappbar
    • Stützfuß hydraulisch
    • Fahrzeugbrief
    • Sonderlackierung (Standart RAL 5010) uvm.